1. No. 147中文

   When inspecting the brakes of a motorcycle, how much free play should there be when lightly pulling the brake lever?

   1. There should be no free play
   2. There should be 1 to 2 cm of free play Correct answer
   3. There should be 3 to 4 cm or more of free play.

2. No. 148中文

   If a motorcycle's muffler is damaged and the rider continues to operate the vehicle without repair, what penalty is imposed according to the Road Traffic Management and Penalty Act?

   1. Fine and order to make corrections Correct answer
   2. Warning from traffic police
   3. Suspension of license plate

3. No. 149中文

   Before starting to drive a motorcycle, the rider should:

   1. Turn on the turn signal and check for obstacles, vehicles, or pedestrians in front, behind, and on both sides Correct answer
   2. Check for passing vehicles on the side
   3. Clearly observe the road surface ahead

4. No. 150中文

   Before starting to drive, the rider should:

   1. Sound the horn
   2. Turn on the turn signal and quickly enter the lane
   3. Turn on the turn signal and check for obstacles, vehicles, or pedestrians in front, behind, and on both sides Correct answer

5. No. 151中文

   When sounding the horn in an emergency or dangerous situation, the principle is to use a single beep, and

   1. do not sound the horn continuously 3 times
   2. each beep should not exceed half a second
   3. all of the above. Correct answer

6. No. 152中文

   Under which of the following conditions should the headlight be turned on while riding?

   1. When encountering dense fog, rain, dim skies, or poor visibility
   2. When passing through a tunnel
   3. All of the above. Correct answer

7. No. 153中文

   Regarding the color of the motorcycle brake light, which of the following is correct?

   1. Red Correct answer
   2. Orange
   3. Yellow.

8. No. 154中文

   Concerning the regulations for motorcycle fog lamps, which of the following is correct?

   1. Front and rear fog lamps should be either one or two lamps
   2. Front fog lamps must be yellow, pale yellow, or white; rear fog lamps must be red
   3. All of the above. Correct answer

9. No. 155中文

   The color of the motorcycle headlight should be

   1. White or pale yellow Correct answer
   2. Blue
   3. No regulation.

10. No. 156中文

    Regarding the regulations for brake lights, which of the following is incorrect?

    1. The light color should be pale yellow Correct answer
    2. When the brake is applied, the light should remain steady and must not flash
    3. The light should be red.

11. No. 157中文

    The color of the turn signal light should be

    1. Red
    2. Yellow
    3. Orange Correct answer

12. No. 158中文

    What is the regulation for the tire diameter of small and light motorcycles? It should be

    1. Between 300 mm and 420 mm Correct answer
    2. Between 200 mm and 400 mm
    3. Between 250 mm and 350 mm

13. No. 159中文

    The curb weight (including battery) of a small light motorcycle should be

    1. 75 kg or less
    2. 70 kg or less Correct answer
    3. 65 kg or less.

14. No. 160中文

    Regarding the heat insulation protective device on motorcycle exhaust pipes:

    1. It does not affect riding operation, so it is not required
    2. It is optional and may or may not be installed
    3. To prevent burns to others, it is required to be installed Correct answer

15. No. 161中文

    Which of the following regarding motorcycle equipment is incorrect?

    1. Horns that emit different tones are not allowed to be installed
    2. Rearview mirrors on both the left and right sides must not be removed
    3. Mudguards may be left uninstalled Correct answer

16. No. 162中文

    After how many years from the motorcycle's manufacture date is a temporary inspection required when transferring ownership?

    1. 5 years Correct answer
    2. 7 years
    3. 10 years

17. No. 163中文

    When a motorcycle is registered as temporarily out of service, what is the maximum allowed period?

    1. 1 year Correct answer
    2. 1.5 years
    3. 2 years

18. No. 164中文

    For a vehicle that has been scrapped:

    1. It is not allowed to apply for registration, inspection, and licensing again Correct answer
    2. It can apply for registration, inspection, and licensing after repairs
    3. There is no regulation

19. No. 165中文

    If a motorcycle is severely damaged in a traffic accident and repaired, which inspection must be carried out?

    1. Regular inspection
    2. Temporary inspection Correct answer
    3. License plate inspection

20. No. 166中文

    The maximum overall height of a motorcycle shall not exceed:

    1. 2 meters Correct answer
    2. 2.5 meters
    3. 3 meters.

21. No. 167中文

    The function of installing rearview mirrors on a motorcycle is to:

    1. increase vehicle stability
    2. allow the driver to conveniently groom themselves
    3. help the driver increase visibility on both sides. Correct answer

22. No. 168中文

    For a scooter-type (continuously variable transmission) motorcycle, the brake levers are controlled as follows:

    1. right hand controls the front brake, left hand controls the rear brake Correct answer
    2. left hand controls the front brake, right hand controls the rear brake
    3. both left and right hands simultaneously control the front and rear brakes.

23. No. 169中文

    If a vehicle is parked unused for a long time, how often should it be started for 3-5 minutes each time to maintain optimal engine starting condition?

    1. Quarterly
    2. Weekly Correct answer
    3. Monthly.

24. No. 170中文

    The normal exhaust color of a gasoline engine is:

    1. black
    2. bluish-white
    3. colorless. Correct answer

25. No. 171中文

    If the exhaust color of a motorcycle engine is black, it may be due to

    1. complete combustion of gasoline
    2. incomplete combustion of gasoline Correct answer
    3. burning of engine oil.

26. No. 172中文

    Which gas in motorcycle exhaust emissions is the main contributor to the greenhouse effect on Earth?

    1. Carbon monoxide
    2. Carbon dioxide Correct answer
    3. Water vapor.

27. No. 173中文

    When checking the motorcycle engine oil, you should

    1. turn off the engine
    2. park on a flat surface
    3. both of the above. Correct answer

28. No. 174中文

    Besides regular inspection, motorcycle engine oil

    1. should be replaced regularly Correct answer
    2. does not need to be replaced
    3. depends on the brand of the oil.

29. No. 175中文

    When adding engine oil, it should be added through which part?

    1. Oil dipstick hole
    2. Engine oil filler cap Correct answer
    3. Fuel tank cap.

30. No. 176中文

    Should the motorcycle oil filter be replaced?

    1. Depends on the brand of engine oil
    2. No need to replace
    3. According to the motorcycle user manual specifications. Correct answer

31. No. 177中文

    At night or in dark places, which lighting tool should NOT be used when checking the battery fluid?

    1. Flashlight
    2. Lighter Correct answer
    3. Electric work light.

32. No. 178中文

    What substance should be applied to the battery terminals to prevent corrosion and ensure good conductivity?

    1. Paint
    2. Grease Correct answer
    3. Tar.

33. No. 179中文

    The power source for the motorcycle starter motor comes from:

    1. Generator supply
    2. Battery supply Correct answer
    3. Engine supply.

34. No. 180中文

    The main purpose of installing an air filter on a motorcycle is:

    1. To prevent sand and dust in the air from damaging the cylinder Correct answer
    2. To reduce motorcycle operating noise
    3. To filter exhaust emissions and reduce pollution.

35. No. 181中文

    When tire pressure is insufficient, it is likely to cause

    1. wear on both sides of the tire Correct answer
    2. wear in the center of the tire
    3. lighter steering.

36. No. 182中文

    When tire pressure is insufficient, it is likely to cause

    1. wear on both sides of the tire
    2. increased fuel consumption
    3. all of the above. Correct answer

37. No. 183中文

    When tire pressure is too high, it is likely to cause

    1. wear on both sides of the tire
    2. wear in the center of the tire Correct answer
    3. increased fuel consumption.

38. No. 184中文

    When tire pressure is too high, it is likely to cause

    1. accelerated damage to the vehicle's shock absorbers
    2. wear in the center of the tire
    3. all of the above. Correct answer

39. No. 185中文

    Severe wear on the center tread of the tire is caused by

    1. tire pressure being too low
    2. tire pressure being too high Correct answer
    3. vehicle overload.

40. No. 186中文

    Excessive tire wear

    1. does not cause danger
    2. provides more comfortable riding
    3. affects vehicle steering and braking distance. Correct answer

41. No. 187中文

    When the tread depth of a motorcycle tire is less than how much should it be replaced?

    1. 2 millimeters
    2. 1.5 millimeters
    3. when it reaches the tire wear indicator. Correct answer

42. No. 188中文

    The motorcycle tire specification 3.50-10-8PR means

    1. tire width is 3.5 inches
    2. tire inner diameter is 10 inches
    3. both of the above. Correct answer

43. No. 189中文

    The main items a driver should check regarding tires are

    1. whether the tire pressure is normal
    2. whether the tire surface has cracks, damage, or abnormal wear
    3. both of the above. Correct answer

44. No. 190中文

    In tire construction, which part has the weakest strength?

    1. tread
    2. sidewall Correct answer
    3. bead.

45. No. 191中文

    When should tire pressure be checked?

    1. After driving when the tire temperature is higher than normal
    2. Before driving when the tire temperature is at normal temperature Correct answer
    3. At any time.

46. No. 192中文

    Low tire pressure can cause

    1. Tire sidewall damage leading to blowouts
    2. Increased rolling resistance resulting in higher fuel consumption
    3. Both of the above. Correct answer

47. No. 193中文

    Tires should be protected by

    1. Avoiding proximity to heat sources
    2. Avoiding contact with mineral oils and related substances
    3. Both of the above. Correct answer

48. No. 194中文

    It is recommended to use tires that are no more than

    1. 3 years
    2. 6 years Correct answer
    3. 9 years old since manufacture.

49. No. 195中文

    What is the primary function of the tread on motorcycle tires?

    1. Water drainage and increased traction Correct answer
    2. Increasing driving speed
    3. Preventing surface cracking of the tire.

50. No. 196中文

    Tire manufacturing date code: MMD1213 indicates

    1. December 2013
    2. the 13th week of 2012
    3. the 12th week of 2013. Correct answer

51. No. 197中文

    The dangers of tire tread being too shallow:

    1. Affects tire friction and grip, easily prolonging braking distance and causing accidents
    2. Poor water drainage on rainy days, increasing the risk of slipping and losing control
    3. All of the above. Correct answer

52. No. 198中文

    Regarding the use of motorcycle rearview mirrors, which is inappropriate?

    1. When traveling very close to the vehicle ahead, you should check the rearview mirror to facilitate overtaking Correct answer
    2. Before riding, adjust the rearview mirrors to angles and positions that make it easy to observe vehicles or road conditions behind
    3. You can adjust the rearview mirrors while waiting at a red light.

53. No. 199中文

    When purchasing a helmet:

    1. It must have a certification label approved by the Standards Inspection Bureau
    2. You should choose a helmet with bright colors or reflective materials
    3. All of the above. Correct answer

54. No. 200中文

    After a helmet has suffered a strong impact:

    1. It should not be used again Correct answer
    2. It can continue to be used if there is no visible damage
    3. It can continue to be used if it is within 3 years from the manufacturing date and has no visible damage.

55. No. 201中文

    If a passenger on a motorcycle is not wearing a helmet,

    1. the driver is penalized Correct answer
    2. the passenger is penalized
    3. no penalty is imposed.

56. No. 202中文

    Which of the following statements is correct?

    1. When the tread surface is level with the tire wear indicator, it means the tire needs to be replaced. Correct answer
    2. When the tread surface is perpendicular to the tire wear indicator, it means the tire needs to be replaced.
    3. When the tread depth at any point on the motorcycle tire reaches 1.6 millimeters, it means the tire needs to be replaced.

57. No. 203中文

    Which of the following is NOT a necessary action before starting to ride?

    1. Check the lights
    2. Confirm tire pressure
    3. Warm up the engine. Correct answer

58. No. 204中文

    Regarding motorcycle rearview mirrors, which statement is incorrect?

    1. Most are convex mirrors
    2. They help riders monitor the situation behind the vehicle
    3. If the rearview mirror cannot properly observe the rear while riding, it should be adjusted immediately during riding. Correct answer

59. No. 205中文

    Regarding motorcycle kickstands, which statement is incorrect?

    1. They can be divided into main stand and side stand
    2. They are parts that require frequent replacement Correct answer
    3. The side stand is less stable and is only recommended for short-term parking.

60. No. 206中文

    Which of the following statements about motorcycle turn signals is incorrect?

    1. Used to alert vehicles in front and behind that the motorcycle intends to turn in a certain direction
    2. The light color should be amber
    3. Whether to signal before turning can be decided based on road conditions Correct answer

61. No. 207中文

    Which of the following about basic motorcycle accessories and functions is correct?

    1. Rearview mirrors hinder smooth weaving through traffic and can be removed if necessary
    2. The headlight includes both high beam and low beam Correct answer
    3. Rearview mirrors are concave mirrors

62. No. 208中文

    If a motorcycle tire blows out while riding, the first action should be:

    1. Brake immediately
    2. Release the throttle Correct answer
    3. Turn the handlebars

63. No. 209中文

    Which of the following motorcycle modifications violate regulations?

    1. Installing high-intensity HID headlights without authorization
    2. Raising the exhaust pipe upwards
    3. Both of the above violate regulations Correct answer

64. No. 210中文

    Principles for selecting a safety helmet:

    1. The tighter the better to prevent it from being blown off
    2. Choose a dark color because it is less likely to get dirty
    3. None of the above Correct answer

65. No. 211中文

    Which of the following will NOT be displayed on a motorcycle dashboard?

    1. High beam indicator
    2. Tire wear indicator Correct answer
    3. Vehicle speed indicator.

66. No. 212中文

    Which of the following is NOT a primary function of a motorcycle suspension system?

    1. Reduce tire wear
    2. Increase engine power Correct answer
    3. Enable safer and more comfortable vehicle handling.

67. No. 213中文

    Motorcycle braking methods should be adjusted according to external conditions. On dry or downhill roads, which braking method is recommended?

    1. Front brake as primary, rear brake as secondary Correct answer
    2. Rear brake as primary, front brake as secondary
    3. Even distribution between front and rear brakes.

68. No. 214中文

    Motorcycle braking methods should be adjusted according to external conditions. On slippery or uphill roads, which braking method is recommended?

    1. Front brake as primary, rear brake as secondary
    2. Rear brake as primary, front brake as secondary Correct answer
    3. Even distribution between front and rear brakes.

69. No. 215中文

    When replacing a motorcycle battery, first turn the main switch key to the "OFF" position, then remove the battery. What is the correct sequence?

    1. Remove the negative cable first, then the positive cable Correct answer
    2. Remove the positive cable first, then the negative cable
    3. Either sequence is acceptable.

70. No. 216中文

    If the air filter accumulates dust, it causes:

    1. reduced horsepower
    2. increased fuel consumption
    3. both of the above. Correct answer

71. No. 217中文

    What does this sign, marking, or signal mean?

    
    1. Vehicle width restriction Correct answer
    2. No parking
    3. Vehicle height restriction.

72. No. 218中文

    What does this sign, marking, or signal mean?

    
    1. Vehicle length restriction Correct answer
    2. Vehicle width restriction
    3. No entry for cars.

73. No. 219中文

    What does this sign, marking, or signal mean?

    
    1. Stop and then proceed
    2. Stop for inspection Correct answer
    3. No pedestrians.

74. No. 220中文

    What does this sign, marking, or signal mean?

    
    1. Stop and then proceed
    2. Stop for inspection Correct answer
    3. No passage.

75. No. 221中文

    When riding a motorcycle, besides checking for fuel, which of the following statements is correct?

    1. No additional basic maintenance is needed.
    2. Basic maintenance is required to ensure the vehicle's condition. Correct answer
    3. Only the tire tread depth needs to be checked.

76. No. 222中文

    If a motorcycle produces abnormal noises when braking, which of the following statements regarding handling is correct?

    1. If the noise occurs only in wet weather and the brakes function normally, it is considered normal and requires no special action.
    2. The motorcycle should be taken as soon as possible to a certified shop for a professional technician to inspect the brake system, identify the cause of the abnormality, and perform necessary repairs. Correct answer
    3. You can check the brake pad thickness yourself, and if it has not worn down to the warning line, there is no safety concern.

77. No. 223中文

    Before riding a motorcycle, a safety inspection should be conducted. Regarding the inspection items, which of the following statements is correct?

    1. Mainly check the brakes and tires; as long as the braking system is normal, it is safe to ride.
    2. Since the motorcycle passed safety inspection before leaving the factory, only periodic maintenance requires a full check.
    3. Check the lights, turn signals, brakes, tires, horn, and rearview mirrors, ensuring all systems function properly. Correct answer

78. No. 224中文

    Regarding safety helmet precautions, which of the following statements is incorrect?

    1. A helmet that has been subjected to impact can still be used normally if the exterior shows no damage, without replacement. Correct answer
    2. The chin strap length should not be too long or too short, leaving about one finger's width of space.
    3. The buckle should be under the chin, leaving one finger's space, and the knob should be tightened.

79. No. 225中文

    When a motorcycle rider and passenger wear a safety helmet, regarding the fastening of the chin strap, which of the following statements is correct?

    1. After fastening the strap, leave about one to two finger-widths of slack to balance comfort and ventilation.
    2. The helmet should be worn facing forward and the chin strap securely fastened, ensuring the helmet fits snugly on the head. Correct answer
    3. For short trips or low-speed riding, the strap only needs to be lightly fastened and does not need to be tight.

80. No. 226中文

    Regarding the selection of a motorcycle safety helmet, which of the following statements is correct?

    1. When choosing a helmet, comfort and ventilation should be the primary considerations.
    2. Select a helmet that bears the commodity inspection mark from the Bureau of Standards, Metrology and Inspection (BSMI) to ensure it meets safety standards. Correct answer
    3. Imported brand helmets that pass international safety certifications have stricter protective performance than domestic standards and can be safely chosen.

81. No. 227中文

    Regarding modification or alteration of motorcycle lights, which of the following statements is correct?

    1. Applying a transparent protective film to the lights to prevent scratches, as long as it does not affect brightness, is compliant.
    2. Installing high-brightness bulbs that have passed inspection to improve nighttime illumination is compliant.
    3. Lights must not be painted, covered with tape, or fitted with additional covers, as this may affect visibility and recognition. Correct answer

82. No. 228中文

    Regarding regulations on modifying motorcycle exhaust pipes, which of the following statements is correct?

    1. Replacing with an exhaust pipe certified by the Environmental Protection Administration (EPA) and meeting emission standards complies with modification regulations.
    2. Using the same model OEM parts to replace the exhaust pipe position, without changing specifications, complies with regulations.
    3. The number and position of exhaust pipes must not be changed, and the muffler or catalytic converter must not be removed. Correct answer

83. No. 229中文

    Before starting the motorcycle engine, which items should be checked?

    1. Only the fuel level.
    2. Only the engine oil level.
    3. Both the engine oil and fuel levels. Correct answer

84. No. 230中文

    When is the most accurate time to measure the engine oil level of a motorcycle?

    1. Immediately after parking and turning off the engine.
    2. When the motorcycle is tilted.
    3. After the motorcycle has been stationary on a level surface for a period of time with the engine off. Correct answer

85. No. 231中文

    Regarding motorcycle tire pressure, which of the following statements is correct?

    1. The higher the tire pressure, the better.
    2. Tire pressure should be lower than the manufacturer's specification to increase grip.
    3. Tire pressure should comply with the manufacturer's specifications, and tread depth should be sufficient. Correct answer

86. No. 232中文

    If a vehicle's tire pressure is "too high," which part of the tire tread will wear most severely?

    1. Both sides of the tread
    2. The inner part of the tread
    3. The center part of the tread Correct answer

87. No. 233中文

    Which of the following on a motorcycle instrument panel is used to indicate the accumulated mileage?

    1. Odometer Correct answer
    2. Speedometer
    3. Tachometer

88. No. 234中文

    When the motorcycle fuel gauge shows "E," what does it mean?

    1. Fuel is sufficient; you can continue riding.
    2. Fuel is low; refuel as soon as possible. Correct answer
    3. Engine oil is low; add engine oil.

89. No. 235中文

    Regarding the periodic inspection regulations for large heavy motorcycles (over 250 cc), which of the following statements is correct?

    1. After a full year from the date of manufacture, the motorcycle must be inspected at least once a year.
    2. Motorcycles less than 5 years from the year of manufacture are exempt from periodic inspections. Correct answer
    3. Motorcycles 5 years or more from the date of manufacture must be inspected once every six months.

90. No. 236中文

    When riding a motorcycle at night, if an oncoming vehicle continuously uses high beams causing glare, which of the following actions best ensures safety?

    1. Respond with high beams to signal the other driver to switch to low beams
    2. Slightly shift your gaze toward the right edge line, maintain a steady speed and lane position, and avoid looking directly at the oncoming lights Correct answer
    3. Slow down and stop by the roadside, waiting for the oncoming vehicle to pass